Shop
Showing 1165–1176 of 1310 results
Sale!
$95.00
Add to cart
TCS Solenoid w/ Bracket
Reproduction TCS Solenoid w/ Mounting Bracket
Fits 1970 - 1973 455 Engines
.
Sale!
$32.00
Add to cart
TCS Switch (Manual Trans – Pin Style)
This is the Pin Style TCS Switch - Replicates GM Part # 3961567 - Connects to Transmission Cover
Fits 1970 - 1972
.
Sale!
$32.00
Add to cart
TCS Switch (Manual Trans – Spade Style)
This is the Spade Style TCS Switch - Replicates GM Part # 3996286 - Connects to Transmission Cover
Fits 1970 - 1972
.
TCS Wire Retainer
This clip holds your TCS Wire to your Muncie 4 Speed Transmission
Fits 1970 - 72
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Sale!
$26.00
Add to cart
Temperature Sending Unit (Gauges)
Temperature Sending Unit - Made in the USA
1970 - 72 GS / GSX with Factory Gauges
Source - Lectric Limited
Note: Most Sending units are there own ground so we do NOT recommend using “Thread Tape” as that can interfere with the Grounding capability.
.
Thermal Air Intake Vacuum Sensor
This is the Cold Air Sensor that mounts in the Air Cleaner Base
Fits 1968 - 1972
Thermal Air Intake Vacuum Sensor Retainer
This is the Retainer that houses the Cold Air (Thermal Air Intake) Sensor to the Air Cleaner assembly
Fits 1968 - 1972
Note: Sensor also available if needed! (Engine Page)
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Sale!
$38.00
Add to cart
Throttle Cable (455)
Big Block Throttle Cable
Total Length (Tip to Tip) is 21"
Housing Length (From Bracket to Firewall) is 10 1/4"
Replaces GM Part # 1387262
Fits 1970 - 1972 455 Engines with Factory Intake & Carburetor
These also fit the 1968-69 Buick's with a 400 engine as well. (Same GM Part #)
350 Cables are different and not reproduced at this time.
.
.
Please Note: When installing this to the Carb Stud make sure it does NOT Stick. It must be able to rotate on the stud!!
When these are New they can be a bit sticky. Please lubricate the ball stud on the carburetor and work the cable back and forth to keep it from sticking.
.
Also Note: IF you're using a different carb and/or intake then you will need to go off of measurements to see if this cable will work. As mentioned earlier it is designed to work with the factory components!
If you need the Throttle Cable Retainer you can purchase them here > https://www.stage1restoration.com/product/throttle-cable-retainer/
.
Throttle Cable Bracket (455)
This is a nice reproduction of the factory 400/455 Throttle Cable Bracket
Fits 1968 - 1972 Big Blocks
Throttle Cable Bracket – 350 Engine
Factory Throttle Cable Bracket for a Buick 350
1970 – 1972 Throttle Cable Bracket for a Buick with a 350 Engine. (might fit other years also)
Note: Not sure if this is for a 2 Barrel or a 4 Barrel Carb so you may want to double check
OEM Parts are Original Equipment that came off a “Parts Car”.
Any of our OEM Parts will always be at least “Driver Quality”
.
. 
Throttle Cable Retainer
This is the Retainer that holds your Throttle Cable to your Gas Pedal
Fits 1968 - 1972 (Maybe more)
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Throttle Return Spring
Throttle Return Spring painted in the correct Green that was used by Buick
Fits V8 Buick Engines from that era.
Note: The diameter of this reproduction spring is a tad smaller than the OEM springs.
Works just fine if you don't have an OEM one laying around.