Shop

Showing 793–804 of 1297 results

Sale!
Hood Tach Harness
Reproduction of the Hood Tach Harness used on 1969 - 1972 Pontiacs. These will work with the aftermarket Hood Tach's that are currently on the market however the wiring Colors are not correct for Buicks. These are made for Pontiac Hood Tach's but will work on the Buick Hood Tach's also. Source – Lectric Limited   We also sell a (Buick) Hood Tach Repair Harness that can be viewed here > Hood Tach Harness.    Note:  We use & sell  Lectric Limited  Products because they’re Made in the USA using Factory GM Blue Prints!
$50.00 Add to cart
Hood Tach Harness Clip
Hood Tach Wire Harness Clip Clip used to attach the Hood Tach Harness to the Hood     .
$10.00 Add to cart
Sale!
Hood Tach Kit
Reproduction Hood Tach as found on the GSX Models Kit provides the following:
  • Hood Tach w/ State of the Art Electronics
  • Detailed Installation Instructions
  • Wiring Harness ( only 3 wires to hook up )
  • Template & Mounting Hardware
Fits 1970 - 1972     Note: The Wiring that comes with this Hood Tach is more consistent with the Pontiac Wiring Colors. If you want the Factory Colored Wires maybe consider our GSX Hood Tach Wire Harness. This will allow you to splice in the correct colored wires that Buick used. If that's not a concern the wiring that comes with the Hood Tach will work fine. The wiring is slightly different than the Factory Hood Tach's so be sure to follow the directions when hooking up the wiring! Plugging this tach into an existing factory harness will NOT work. These have modern electronics and need to be wired as the directions indicate!   Note # 2: We've seen Factory GSX Hoods with Holes ranging from 3 3/4" to 4" in diameter to accept the Factory Hood Tach's. This Reproduction hood tach requires a hole that is roughly 4 1/4" in Diameter.   .
$219.00 Add to cart
Sale!
Hood Tach Light Harness
Reproduction of the Hood Tach Light Harness used on 1970 - 1972 GSX Source – Lectric Limited   Note:  We use & sell  Lectric Limited  Products because they’re Made in the USA using Factory GM Blue Prints!
$28.00 Add to cart
Hood Tach Mounting Nuts
Factory Hood Tach Flange Nuts (Phosphate) These are the correct Phosphate Flange Nuts that Buick used on there Hood Tach's Fits 1970 - 1972 Factory Hood Tach's   Note: These will not work on the current Aftermarket Hood Tach's.  
$3.00 Add to cart
Hood Tach Repair Harness
Hood Tach Repair Harness Use this harness to repair or freshen up your GSX Hood Tach Harness. This is a 36" section of Factory Wiring that you can splice in to repair or freshen up your existing harness. Also included is a 20" section that is used along with the Ignition Coil Wire. (includes the Factory Weather Proof Junction Plug) This will also work well for someone using an Aftermarket Hood Tach that wants the correct colored wires. The 3 wires are as follows:
  • Black - Ground
  • Grey - Tach Lights
  • Brown - Signal Wire (To Coil)
  This Harness utilizes the factory connector as used by Buick. Made by Lectric Limited exclusively for Stage1Restoration! You won't find these anywhere else!   .
$25.00 Add to cart
Horn Cap Emblem
Buick Horn Cap Emblem for the 3 Spoke Rallye Steering Wheel Fits 1970 - 1972 Buick Horn Caps (Does Fit other years as well) This is a nice reproduction!   Note: Be sure to line up the notch at the bottom of the emblem with the tab in the Horn Cap Housing. This will "clock" the emblem properly which is important for proper alignment of the Cap to the Retainer it snaps in to. The Red Circles need to match once the Cap is Snapped into place. This will allow the Horn Cap to fit properly and function  properly!        
$39.00 Add to cart
Sale!
Horn Cap For Rallye Wheels
Replacement Horn Cap in Black for the Rallye Steering Wheels Fits 1969 - 1972     Note: The manufacture of these does not install the "Buick" Emblem so when you go to install it be sure to line up the notch at the bottom of the emblem with the tab in the Horn Cap Housing. This will "clock" the emblem properly which is important for proper alignment of the Cap to the Retainer it snaps in to. The Red Circles need to match once the Cap is Snapped into place. This will allow the Horn Cap to fit properly and function  properly!   The photo below shows the back side of the Horn Cap (Left Side of Photo) and where the 3 cutouts should be to snap into the retainer properly. If you have any questions on this feel free to call me!    
$65.00 Add to cart
Horn Cap Mounting Kit (Non Tilt)
This is a replacement Horn Contact & Horn Cap Mounting Kit for anyone using the 3 Spoke Rallye Steering Wheels (Non Tilt) Kit Includes:
  • Cancel Cam
  • 6) Steering Wheel to Hub Screws
  • 3) Horn Cap Retainer to Hub Screws
  • Horn Cap Retainer (Contact)
  • Horn "Contact Pin"
  • Horn "Spring"
  • Horn Spring Retainer (Insulator)
    Note:  The Aluminum "Contact Pin" is a tad long on purpose.  Trim to proper length for your application. Generally 3/4" is just about right.   Note: For a Bigger Photo of this click here     For a bigger picture of this Diagram please see Picture # 32 on our Factory Diagrams Page            
$36.00 Add to cart
Horn Cap Mounting Kit (Tilt)
This is a replacement Horn Contact & Horn Cap Mounting Kit for anyone using the 3 Spoke Rallye Steering Wheels (For Tilt Columns) Kit Includes:
  • Cancel Cam
  • 6) Steering Wheel to Hub Screws
  • 3) Horn Cap Retainer to Hub Screws
  • Horn Cap Retainer (Contact)
  • Horn “Contact Pin”
  • Horn “Spring”
  • Horn Spring Retainer (Insulator)
    Note:  The Aluminum "Contact Spring" is a tad long on purpose.  Trim to proper length for your application. Generally 3/4″ is just about right.   Note: For a Bigger Photo of this click here     For a bigger picture of this Diagram please see Picture # 32 on our Factory Diagrams Page  
$35.00 Add to cart
Horn Cap Mounting Schematic
Here is the Factory Horn Cap Mounting Schematic for Buick's 3 Spoke Steering Wheel . . . .     For a bigger picture of this Diagram please see Picture # 32 on our Factory Diagrams Page
$0.00 Read more
Horn Cap Retainer
Replacement Horn Cap Retainer (Not as good as the OEM Pcs but these will work if you don't have an original) Fits All Models using a 3 Spoke Rallye Type Steering Wheel       Note: For a Bigger Photo of this click here   .
$19.00 Add to cart