Shop

Showing 757–768 of 1297 results

Heater Box Hardware Kit (Non A/C)
Heater Box Hardware Kit for Non A/C Car Kit includes proper hardware for :
  • Blower Motor Case to Firewall (2 Screws - 5 Nuts)
  • Blower Motor to Blower Motor Case (5 Hex Screws)
  • Blower Motor Wire Clip ( 1 )
  Fits 1970 - 1972 GS, GSX & Skylark     Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ?  Give me a call, we probably have it!  
$12.00 Add to cart
Heater Box Seal Kit (A/C)
Heater Box Seal Kit for cars with A/C Fits 1968 - 1972   .
$29.00 Add to cart
Heater Box Seal Kit (Non A/C)
Heater Box Seal Kit for cars without A/C Fits 1968 - 1972   .
$28.00 Add to cart
Heater Cable Retainer Clips

Pack of 8 Heater Cable Retainer Clips  -  5/32 Push nut  (.44)  Phosphate

Fits Most GM Cars of that era     Note: The 1970 - 72 Buick's only require 6 of these but we provide 8 in case extra's are needed.   Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ?  Give me a call, we probably have it! .
$4.00 Add to cart
Heater Control Valve
This is used on cars with A/C Fits 1966 - 1972   If you need the correct Tower Clamps we have them - Control Valve Tower Clamps   .  
$43.00 Add to cart
Heater Core Retainer Clips
This 2 Pc Clip Set holds the Heater Core inside the Heater Box Fits 1964 - 1972     Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ?  Give me a call, we probably have it!  
$29.00 Add to cart
Heater Core Seal (A/C)
Heater Core Seal for cars with A/C Fits 1968 - 1972   .
$4.00 Add to cart
Heater Hose (3/4″ – Ribbed)
5 Foot Pc of 3/4" Ribbed Heater Hose Fits Buick V8 Engines with or without A/C     Note: The 3/4" Ribbed Heater Hose has been discontinued. We're trying to locate a new vendor for this product.   .
$18.00 Read more
Heater Hose (5/8″ – Ribbed)
5 Foot Piece of 5/8" Ribbed Heater Hose Fits Buick V8 Engines with or without A/C     Note: The 5/8″ Ribbed Heater Hose has been discontinued. We're trying to locate a new vendor for this product.   .
$18.00 Read more
Heater Hose & Radiator Hose Clamp Kit – A/C
Going by the Chassis Manuals these are the Correct Clamps used on the Heater Hoses,  Bypass Hose & Radiator Hoses on Buick V8 Engines with A/C This Kit provides:
  • 2)  Bypass Hose Clamps
  • 2)  5/8" Heater Hose Clamps
  • 2)  3/4" Heater Hose Clamps
  • 2)  5/8" Tower Clamps for the Control Valve
  • 4)  2 1/16" Tower Clamps for the Radiator Hoses
Fits 1970 - 1972 Buick V8 Engines with A/C  -  (Correct for other Years also)     Note: The Tower clamps are made by Wittek which is who Buick sourced back in the day however we feel these clamps aren't quite the quality they use to be. For better results lubricate the entire clamp prior to installation. This helps the clamp tighten down properly. The lubrication eliminates some of the resistance during the tightening process. Make sure the bolt stays straight during the tightening process as well.       Photo below was taken from a 1970 Buick Chassis Manual.  (1971 & 1972 Correspond as well)   Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ?  Give me a call, we probably have it!    
$28.00 Add to cart
Heater Hose & Radiator Hose Clamp Kit – Non A/C
Going by the Chassis Manuals these are the Correct Clamps used on the Heater Hoses,  Bypass Hose & Radiator Hoses on Buick V8 Engines. This Kit provides:
  • 2)  Bypass Hose Clamps
  • 2)  5/8" Heater Hose Clamps
  • 2)  3/4" Heater Hose Clamps
  • 4)  2 1/16" Tower Clamps for the Radiator Hoses
Fits 1970 - 1972 Buick V8 Engines without A/C  -  (Correct for other Years also)     Note: The Tower clamps are made by Wittek which is who Buick sourced back in the day however we feel these clamps aren't quite the quality they use to be. For better results lubricate the entire clamp prior to installation. This helps the clamp tighten down properly. The lubrication eliminates some of the resistance during the tightening process. Make sure the bolt stays straight during the tightening process as well.       Photo below was taken from a 1970 Buick Chassis Manual.  (1971 & 1972 Correspond as well)   Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ?  Give me a call, we probably have it!  
$22.00 Add to cart
Heater Hose Bracket – 1969 – 1970
This is a nice reproduction of the Heater Hose Bracket found on the 1969 & 1970 Models. Made in the USA   (Small run so these won't last long)  Properly phosphate coated as well! Fits 1969 & 1970  -  400 & 455 Engines Mounting Hardware included. (We've seen these mounted with a Flange Bolt as well as a Regular Hex Head bolt so we include 1 of each!)    
$69.00 Add to cart