Transmission / Automatic
Showing 37–48 of 69 results
Floor Shift Handle Cradle
This is the (Shifter Cradle) for the Automatic Floor Shift assembly used by Buick
Fits 1970 - 1972
4 pcs total
It is crucial that you use the Proper Phillips Screws when installing the Handle and Pull bar or the shifter will not slide up and down properly!
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
Note: If you're also using the aftermarket Chrome Shifter Handle Insert you will want to drill out the holes shown below to 5/16". We've found that the Chrome Shifter Handle Inserts are a tad to short to properly snap into the shifter cradle. See photos below for more on this!
The Circled area shows the hole that needs to be "enlarged". In most cases you can simply drill this hole out to 5/16". (It's currently a 1/4" hole) The bigger hole allows for the Tabs on the Chrome Insert to lock in place. IF you still have a Factory Handle Insert then you may not need to do this.
If needed you can also take a hand file or dremel tool and enlarge the hole towards the TOP!
This will allow the Chrome Insert to Snap in to place easier.
You're basically enlarging the holes so that the Shifter Insert Tabs will snap in to the Cradle better.
Note: If you're also using the aftermarket Chrome Shifter Handle Insert you will want to drill out the holes shown below to 5/16". We've found that the Chrome Shifter Handle Inserts are a tad to short to properly snap into the shifter cradle. See photos below for more on this!
The Circled area shows the hole that needs to be "enlarged". In most cases you can simply drill this hole out to 5/16". (It's currently a 1/4" hole) The bigger hole allows for the Tabs on the Chrome Insert to lock in place. IF you still have a Factory Handle Insert then you may not need to do this.
If needed you can also take a hand file or dremel tool and enlarge the hole towards the TOP!
This will allow the Chrome Insert to Snap in to place easier.
You're basically enlarging the holes so that the Shifter Insert Tabs will snap in to the Cradle better.
Floor Shift Handle Insert (Aluminum Version)
Reproduction of the Chrome Insert that's inserted into the Shift Handle.
This is the Polished Aluminum Version made by Michael Garrison
Fits 1970 - 72
Source - HTR
Floor Shift Handle Insert (Plastic Version)
Reproduction of the Chrome Insert that's inserted into the Shift Handle.
This is the Plastic Version
Fits 1970 - 72
Note: Unfortunately these do not fit perfectly without a little "Fine Tuning". We've found that most of these are a tad to short to properly snap into the shifter cradle. So if you purchase this item be aware that some fine tuning may be required to fit perfectly. If you don't want to go through this process I recommend trying to find a nice original piece. Otherwise if you simply open up the holes that the Tabs at the bottom fit into it will work much better. See photos below for more on this!
The Circled area shows the hole that needs to be "enlarged". In most cases you can simply drill this hole out to 5/16". (It's currently a 1/4" hole) The bigger hole allows for the Tabs on the Chrome Insert to lock in place.
If needed you can also take a hand file or dremel tool and enlarge the hole towards the TOP!
This will allow the Chrome Insert to Snap in to place easier.
You're basically enlarging the holes so that the Shifter Insert Tabs will snap in to the Cradle better.
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
If needed you can also take a hand file or dremel tool and enlarge the hole towards the TOP!
This will allow the Chrome Insert to Snap in to place easier.
You're basically enlarging the holes so that the Shifter Insert Tabs will snap in to the Cradle better.
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
Floor Shift Handle Pull Bar
This is commonly referred to as the "Pull Bar" for an automatic Floor Shift
Fits 1970 - 72
It is crucial that you use the Proper Phillips Screws when installing the Handle and Pull bar or the shifter will not slide up and down properly!
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
Also, when installing the screws that hold the handle & the pull bar in place be sure to place some lube on them and install slowly!! (Otherwise you can crack the plastic)
It is crucial that you use the Proper Phillips Screws when installing the Handle and Pull bar or the shifter will not slide up and down properly!
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
Also, when installing the screws that hold the handle & the pull bar in place be sure to place some lube on them and install slowly!! (Otherwise you can crack the plastic)
Floor Shift Handle Release Springs
These are the springs that are inside the Floor Shift Handle and help release the Pull Bar
Fits 1970 - 72
Sold as a Pair
If you need the Correct Hardware for your Floor Shifter be sure to check out our Floor Shift Hardware Kit
Floor Shift Pivot Bushings
1968 - 1977 Buick Floor Shift Pivot Bushings
These are only available here!
Made in the USA
Sold as a Pair for $18
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Inspection Cover Bolt Kit – Automatic Trans
Flexplate Inspection Cover bolts
Typically Fits 1964 - 1972 GM Automatic Transmissions
Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models.
Don’t see what you need ? Give me a call, we probably have it!
Mini Console Mounting Brackets
These are the Brackets that hold the Mini Console in place (located in between a set of Bucket Seats)
Could be used on Column Shift Cars or Manual Shift Cars (with Bucket Seats)
Fits 1970 - 1972 (Maybe more)
Sale!
$485.00
Add to cart
Shifter Assembly (Complete) 1970
Buick Floor Shifter - Brown Handle
These are Brand New and only available here!
High Quality - Precision Factory Shifters!
Comes Fully Assembled!
The following is included with this purchase:
- Shifter Base
- Shifter Handle (Brown)
- Shifter Handle Cradle
- Detent Plate
- Shift Cable Retaining Clip
- Chrome Handle Insert
- Chrome Handle Pull Bar
- Handle Springs
- Floor Shift Hardware Mounting Kit
- Shifter Schematic
- Handle Bushings - Made in the USA!
Sale!
$485.00
Add to cart
Shifter Assembly (Complete) 1971/72
Buick Floor Shifter - Black Handle
These are Brand New and only available here!
High Quality - Precision Factory Shifters!
Comes Fully Assembled!
The following is included with this purchase:
- Shifter Base
- Shifter Handle (Black)
- Shifter Handle Cradle
- Detent Plate
- Shift Cable Retaining Clip
- Chrome Handle Insert
- Chrome Handle Pull Bar
- Handle Springs
- Floor Shift Hardware Mounting Kit
- Shifter Schematic
- Handle Bushings - Made in the USA!
Shifter Base
Buick Floor Shifter (Limited Quantities)
These are Brand New and only available here!
We're offering just the base for our customers that may already have some parts but not a complete shifter.
The following items are included:
- Shifter Base
- Pivot Handle
- Pivot Handle Bushings - Made in the USA
Speedometer Cable – 62″
62" Speedo Cable
This length is typically used on Automatic Trans Cars (1970-1972)
It's also used on Manual Trans cars WITH the Side Adapter.
It's a tad longer than stock but this is the closest length we've found to the originals.