Engine Parts

Showing 109–120 of 189 results

Heat Shield (350 Exhaust Manifold)
Reproduction of the Driver Side Heat Shield Fits - 1968 - 1972 Buick 350   .
$99.00 Add to cart
Heat Shield (455 Exhaust Manifold)
Reproduction of the 1970 455 Driver Side Heat Shield. Can use on newer 455 Engines but a small notch will need to be cut near the rear of the Heat Shield - See Photos below . . . Fits - Buick 455     Photos below show the notch that may need to be cut in if used on new Exhaust Manifolds. This notch is approximately 1" wide. Close up of notch "cut out" towards the rear of the Heat Shield.  
$109.00 Add to cart
Heat Shield (Motor Mount)
Reproduction Heat Shield for the Passenger Side Motor Mount Fits 400 - 430 - 455    
$25.00 Add to cart
Heat Shield (Starter)
Reproduction Heat Shield found on Buick Engines Fits 350 - 400 - 430 - 455    
$39.00 Add to cart
Heat Stove – 350
This is an OEM Part  Fits 1970 – 1972 Skylark, GS & GSX with 350 Engine. (maybe other years as well) These are NOT currently reproduced and somewhat hard to find. It’s been cleaned, bead blasted and painted with High Temp Primer . . This Part has Sold Out but we leave hard to find parts like this on the website so you can use the photo and information to help locate one! . OEM Parts are Original Equipment that came off a “Parts Car”. Any of our OEM Parts will always be at least “Driver Quality”    
$0.00 Read more
Heat Stove Mounting Bolts (Pair)
Heat Stove Mounting Bolts - Sold as a Pair (Requires 2) Fits 1970 - 1972 Source - Stage 1 Restoration     Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ?  Give me a call, we probably have it!  
$2.00 Add to cart
Heat Stove Pipe (Black)
This is the Black Piping that goes from the heat stove to the bottom side of the Air Cleaner Assembly Also called a "Pre Heat Tube" Fits 1970 - 1972  (Maybe More)     Note: Our Heat Stove Pipe is the correct length. Be aware of other Vendors not providing a long enough piece! Black was typically used on the GS, GSX & Skylark Models.   We know our parts fit because we use them in our Restoration Shop!     Installation Tip: The Heat Stove Pipe "Threads" onto the Air Cleaner Elbow. Install this end 1st then it simply slides onto the Heat Stove. The picture below shows the "threads" that the heat stove utilizes . . . .     .
$19.00 Add to cart
Heater Hose & Radiator Hose Clamp Kit – A/C
Going by the Chassis Manuals these are the Correct Clamps used on the Heater Hoses,  Bypass Hose & Radiator Hoses on Buick V8 Engines with A/C This Kit provides:
  • 2)  Bypass Hose Clamps
  • 2)  5/8" Heater Hose Clamps
  • 2)  3/4" Heater Hose Clamps
  • 2)  5/8" Tower Clamps for the Control Valve
  • 4)  2 1/16" Tower Clamps for the Radiator Hoses
Fits 1970 - 1972 Buick V8 Engines with A/C  -  (Correct for other Years also)     Note: The Tower clamps are made by Wittek which is who Buick sourced back in the day however we feel these clamps aren't quite the quality they use to be. For better results lubricate the entire clamp prior to installation. This helps the clamp tighten down properly. The lubrication eliminates some of the resistance during the tightening process. Make sure the bolt stays straight during the tightening process as well.       Photo below was taken from a 1970 Buick Chassis Manual.  (1971 & 1972 Correspond as well)   Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ?  Give me a call, we probably have it!    
$28.00 Add to cart
Heater Hose & Radiator Hose Clamp Kit – Non A/C
Going by the Chassis Manuals these are the Correct Clamps used on the Heater Hoses,  Bypass Hose & Radiator Hoses on Buick V8 Engines. This Kit provides:
  • 2)  Bypass Hose Clamps
  • 2)  5/8" Heater Hose Clamps
  • 2)  3/4" Heater Hose Clamps
  • 4)  2 1/16" Tower Clamps for the Radiator Hoses
Fits 1970 - 1972 Buick V8 Engines without A/C  -  (Correct for other Years also)     Note: The Tower clamps are made by Wittek which is who Buick sourced back in the day however we feel these clamps aren't quite the quality they use to be. For better results lubricate the entire clamp prior to installation. This helps the clamp tighten down properly. The lubrication eliminates some of the resistance during the tightening process. Make sure the bolt stays straight during the tightening process as well.       Photo below was taken from a 1970 Buick Chassis Manual.  (1971 & 1972 Correspond as well)   Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ?  Give me a call, we probably have it!  
$22.00 Add to cart
Heater Hose Bracket – 1969 – 1970
This is a nice reproduction of the Heater Hose Bracket found on the 1969 & 1970 Models. Made in the USA   (Small run so these won't last long)  Properly phosphate coated as well! Fits 1969 & 1970  -  400 & 455 Engines Mounting Hardware included. (We've seen these mounted with a Flange Bolt as well as a Regular Hex Head bolt so we include 1 of each!)    
$69.00 Add to cart
Heater Hose Bracket – 1971/72
This is an OEM Part  Factory Heater Hose Bracket Cleaned and Bead Blasted Fits 1971 – 1972 Skylark, GS & GSX with 455 Engine These are NOT currently reproduced and somewhat hard to find. . . This Part has Sold Out but we leave hard to find parts like this on the website so you can use the photo and information to help locate one! . OEM Parts are Original Equipment that came off a “Parts Car”. Any of our OEM Parts will always be at least “Driver Quality”         OEM Parts are Original Equipment that came off a “Parts Car”. Any of our OEM Parts will always be at least “Driver Quality”
$0.00 Read more
Heater Hose Clamps – For A/C Cars
Going by the Chassis Manuals these are the Correct Clamps used on the Heater Hoses, Bypass Hose & Control Valve on Buick V8 Engines with A/C This Kit provides:
  • 2)  Bypass Hose Clamps
  • 2)  5/8" Heater Hose Clamps
  • 2)  3/4" Heater Hose Clamps
  • 2)  5/8" Tower Clamps for the Control Valve used on A/C Cars
Fits 1970 - 1972 Buick V8 Engines with A/C  -  (Correct for other Years also)     Note: The Tower clamps are made by Wittek which is who Buick sourced back in the day however we feel these clamps aren't quite the quality they use to be. For better results lubricate the entire clamp prior to installation. This helps the clamp tighten down properly. The lubrication eliminates some of the resistance during the tightening process. Make sure the bolt stays straight during the tightening process as well.       Photo below was taken from a 1970 Buick Chassis Manual.  (1971 & 1972 Correspond as well)   Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ?  Give me a call, we probably have it!    
$15.00 Add to cart