Clips, Clamps & Brackets – Page 6 – StageWonRestoration.com & DieCastMuscleCars.com

GSX Rear Spoiler Brackets

Rear GSX Spoiler Brackets These mount inside the trunk lid to give it some rigidity when mounting a rear spoiler Fits 1970 - 1972 Skylark, GS & GSX Deck Lids .

$30.00 Add to cart

GSX Rear Spoiler Mounting Kit (Hardware & Brackets)

1970 - 1972 Rear Spoiler Hardware Mounting Kit Kit includes the following:

2 Mounting Studs (Self Tapping on Spoiler Side)
2 Gold Cad Mounting Nuts
2 Self Tapping Mounting Hex Screws
2 Rear Spoiler Mounting Brackets

This is by far the best kit on the market in terms of accuracy! Note: Both the Nuts and the Hex Screws require a 7/16" Socket Note: This kit is designed to mount a Factory or Reproduction Spoiler that has not had it's mounting holes altered! (Or enlarged) Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ? Give me a call, we probably have it!

$50.00 Add to cart

Headliner Bow Clip

This is the Clip used to hold your Headliner Bow's in place $5.00 Each (Usually requires 4 per car) Fits 1968 - 1972 Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ? Give me a call, we probably have it!

$5.00 Add to cart

Headliner Bow Clip / Retainer

This is the Clip that holds the Headliner Bow's in place as well as the Dome Light Wiring $5.00 Each - Usually requires 6 per car Fits 1964 - 1972 Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ? Give me a call, we probably have it!

$5.00 Add to cart

Heater Cable Retainer Clips

Pack of 8 Heater Cable Retainer Clips - 5/32 Push nut (.44) Phosphate

Fits Most GM Cars of that era Note: The 1970 - 72 Buick's only require 6 of these but we provide 8 in case extra's are needed. Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ? Give me a call, we probably have it! .

$4.00 Add to cart

Heater Core Retainer Clips

This 2 Pc Clip Set holds the Heater Core inside the Heater Box Fits 1964 - 1972 Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ? Give me a call, we probably have it!

$29.00 Add to cart

Heater Hose & Radiator Hose Clamp Kit – A/C

Going by the Chassis Manuals these are the Correct Clamps used on the Heater Hoses, Bypass Hose & Radiator Hoses on Buick V8 Engines with A/C This Kit provides:

2) Bypass Hose Clamps
2) 5/8" Heater Hose Clamps
2) 3/4" Heater Hose Clamps
2) 5/8" Tower Clamps for the Control Valve
4) 2 1/16" Tower Clamps for the Radiator Hoses

Fits 1970 - 1972 Buick V8 Engines with A/C - (Correct for other Years also) Note: The Tower clamps are made by Wittek which is who Buick sourced back in the day however we feel these clamps aren't quite the quality they use to be. For better results lubricate the entire clamp prior to installation. This helps the clamp tighten down properly. The lubrication eliminates some of the resistance during the tightening process. Make sure the bolt stays straight during the tightening process as well. Photo below was taken from a 1970 Buick Chassis Manual. (1971 & 1972 Correspond as well)

Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ? Give me a call, we probably have it!

$28.00 Add to cart

Heater Hose & Radiator Hose Clamp Kit – Non A/C

Going by the Chassis Manuals these are the Correct Clamps used on the Heater Hoses, Bypass Hose & Radiator Hoses on Buick V8 Engines. This Kit provides:

2) Bypass Hose Clamps
2) 5/8" Heater Hose Clamps
2) 3/4" Heater Hose Clamps
4) 2 1/16" Tower Clamps for the Radiator Hoses

Fits 1970 - 1972 Buick V8 Engines without A/C - (Correct for other Years also) Note: The Tower clamps are made by Wittek which is who Buick sourced back in the day however we feel these clamps aren't quite the quality they use to be. For better results lubricate the entire clamp prior to installation. This helps the clamp tighten down properly. The lubrication eliminates some of the resistance during the tightening process. Make sure the bolt stays straight during the tightening process as well. Photo below was taken from a 1970 Buick Chassis Manual. (1971 & 1972 Correspond as well)

Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ? Give me a call, we probably have it!

$22.00 Add to cart

Heater Hose Bracket – 1969 – 1970

This is a nice reproduction of the Heater Hose Bracket found on the 1969 & 1970 Models. Made in the USA (Small run so these won't last long) Properly phosphate coated as well! Fits 1969 & 1970 - 400 & 455 Engines Mounting Hardware included. (We've seen these mounted with a Flange Bolt as well as a Regular Hex Head bolt so we include 1 of each!)

$69.00 Add to cart

Heater Hose Bracket – 1971/72

This is an OEM Part Factory Heater Hose Bracket Cleaned and Bead Blasted Fits 1971 – 1972 Skylark, GS & GSX with 455 Engine These are NOT currently reproduced and somewhat hard to find. . . This Part has Sold Out but we leave hard to find parts like this on the website so you can use the photo and information to help locate one! . OEM Parts are Original Equipment that came off a “Parts Car”. Any of our OEM Parts will always be at least “Driver Quality”

OEM Parts are Original Equipment that came off a “Parts Car”. Any of our OEM Parts will always be at least “Driver Quality”

$0.00 Read more

Heater Hose Clamps – For A/C Cars

Going by the Chassis Manuals these are the Correct Clamps used on the Heater Hoses, Bypass Hose & Control Valve on Buick V8 Engines with A/C This Kit provides:

2) Bypass Hose Clamps
2) 5/8" Heater Hose Clamps
2) 3/4" Heater Hose Clamps
2) 5/8" Tower Clamps for the Control Valve used on A/C Cars

Fits 1970 - 1972 Buick V8 Engines with A/C - (Correct for other Years also) Note: The Tower clamps are made by Wittek which is who Buick sourced back in the day however we feel these clamps aren't quite the quality they use to be. For better results lubricate the entire clamp prior to installation. This helps the clamp tighten down properly. The lubrication eliminates some of the resistance during the tightening process. Make sure the bolt stays straight during the tightening process as well. Photo below was taken from a 1970 Buick Chassis Manual. (1971 & 1972 Correspond as well)

Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ? Give me a call, we probably have it!

$15.00 Add to cart

Heater Hose Clamps – Non A/C

Going by the Chassis Manuals these are the Correct Clamps used on the Heater Hoses and the Bypass Hose on Buick V8 Engines. This Kit provides:

2) Bypass Hose Clamps
2) 5/8" Heater Hose Clamps
2) 3/4" Heater Hose Clamps

Fits 1970 - 1972 Buick V8 Engines without A/C - (Correct for other Years also) Photo below was taken from a 1970 Buick Chassis Manual. (1971 & 1972 Correspond as well)

Stage 1 Restoration has the most hardware of any vendor for the 1970 – 1972 GS / GSX & Skylark Models. Don’t see what you need ? Give me a call, we probably have it!

$10.00 Add to cart